DataSheet.jp

HS-26C32RH-T の電気的特性と機能

HS-26C32RH-TのメーカーはIntersilです、この部品の機能は「Radiation Hardened Quad Differential Line Receiver」です。


製品の詳細 ( Datasheet PDF )

部品番号 HS-26C32RH-T
部品説明 Radiation Hardened Quad Differential Line Receiver
メーカ Intersil
ロゴ Intersil ロゴ 




このページの下部にプレビューとHS-26C32RH-Tダウンロード(pdfファイル)リンクがあります。
Total 3 pages

No Preview Available !

HS-26C32RH-T Datasheet, HS-26C32RH-T PDF,ピン配置, 機能
®
Data Sheet
HS-26C32RH-T
August 1, 2008
FN4592.2
Radiation Hardened Quad Differential Line
Receiver
Intersil’s Satellite Applications Flow™ (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. These QML
Class T devices are processed to a standard flow intended
to meet the cost and shorter lead-time needs of large volume
satellite manufacturers, while maintaining a high level of
reliability.
The Intersil HS-26C32RH-T is a Quad Differential Line
Receiver designed for digital data transmission over
balanced lines and meets the requirements of EIA Standard
RS-422. Radiation Hardened CMOS processing assures low
power consumption, high speed, and reliable operation in
the most severe radiation environments.
The HS-26C32RH-T has an input sensitivity of 200mV (typ).
over the common mode input voltage range of ±7V. The
receivers are also equipped with input fail safe circuitry,
which causes the outputs to go to a logic “1” when the inputs
are open. Enable and Disable functions are common to all
four receivers.
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-26C32RH-T
are contained in SMD 5962-95689. A “hot-link” is provided
from our website for downloading.
http://www.intersil.com/military/
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
http://rel.intersil.com/reports/search.php
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose . . . . . . . . . . . . . . . . . . . . 1 x 105 RAD(Si)
- SEU and SEL . . . . . . . . . . Immune to 100MeV/mg/cm2
• EIA RS-422 Compatible Inputs
• CMOS Compatible Enable Inputs
• Input Fail Safe Circuitry
• High Impedance Inputs when Disabled or Powered Down
• Low Power Dissipation 138mW Standby (Max)
• Single 5V Supply
• Full -55°C to +125°C Military Temperature Range
Applications
• Line Receiver for MIL-STD-1553 Serial Data Bus
Functional Diagram
ENABLE ENABLE DIN DIN
CIN CIN
BIN BIN AIN AIN
+-
+-
+-
+-
DOUT
COUT
BOUT
AOUT
Ordering Information
ORDERING NUMBER
INTERNAL MKT. NUMBER
PART MARKING
5962R9568901TEC
HS1-26C32RH-T
Q 5962R95 68901TEC
HS1-26C32RH/PROTO
HS1-26C32RH/PROTO
HS1- 26C32RH /PROTO
5962R9568901TXC
HS9-26C32RH-T
Q 5962R95 68901TXC
HS9-26C32RH/PROTO
HS9-26C32RH/PROTO
HS9- 26C32RH /PROTO
NOTE: Minimum order quantity for -T is 150 units through distribution, or 450 units direct.
TEMP. RANGE
(°C)
PACKAGE
PKG. DWG. #
-55 to +125 16 Ld SBDIP
D16.3
-55 to +125 16 Ld SBDIP
D16.3
-55 to +125 16 Ld FLATPACK K16.A
-55 to +125 16 Ld FLATPACK K16.A
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2002, 2008. All Rights Reserved
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation. All other trademarks mentioned are the property of their respective owners..

1 Page





HS-26C32RH-T pdf, ピン配列
HS-26C32RH-T
Die Characteristics
DIE DIMENSIONS:
2140µm x 3290µm x 533μm ±25.4µm
(85 x 130 x 21mils ±1mil)
METALLIZATION:
M1: Mo/Tiw
Thickness: 5800Å
M2: Al/Si/Cu
Thickness: 10kÅ ±1kÅ
SUBSTRATE POTENTIAL:
Internally connected to VDD. May be left floating.
Metallization Mask Layout
AIN
(1)
BACKSIDE FINISH:
Silicon
PASSIVATION:
Type: SiO2
Thickness: 8kÅ ±1kÅ
WORST CASE CURRENT DENSITY:
< 2.0e5 A/cm2
TRANSISTOR COUNT:
315
PROCESS:
Radiation Hardened CMOS, AVLSI
HS-26C32RH
VDD
(16)
BIN
(15)
AIN (2)
(14) BIN
AOUT (3)
ENAB (4)
(13) BOUT
(12) ENAB
COUT (5)
(11) DOUT
CIN (6)
(10) DIN
(7) (8) (9)
CIN
GND
DIN
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
3 FN4592.2
August 1, 2008


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ HS-26C32RH-T データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HS-26C32RH-T

Radiation Hardened Quad Differential Line Receiver

Intersil
Intersil


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap