|
|
PDF PTCCL05H150HTE Data sheet ( Hoja de datos )
| Número de pieza | PTCCL05H150HTE | |
| Descripción | 265 V PTC Thermistors | |
| Fabricantes | Vishay | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PTCCL05H150HTE (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
www.vishay.com
PTCCL - 265 V Series
Vishay BCcomponents
265 V PTC Thermistors for Overload Protection
QUICK REFERENCE DATA
PARAMETER
VALUE
Maximum voltage (RMS or DC)
265
Maximum holding current (Int)
Resistance at 25 °C (R25)
Tolerance on R25 value
Maximum overload current Iol
Switching temperature
0.011 to 0.8
2.1 to 3000
20
0.8 to 5.5
135 to 145
Operating temperature range
at max. voltage
0 to 70
Storage temperature
-40 to +175
UNIT
V
A
Ω
%
A
°C
°C
°C
QUALITY
UL approved PTCs are guaranteed to withstand severe test
programs and have factory audited follow-up programs.
Major UL qualification tests are long-life (6000 cycles)
electrical cycle tests at trip-current, long-life stability
storage tests (3000 h at 250 °C), damp heat and water
immersion tests and over-voltage tests up to 200 % of rated
voltage.
UL approved PTCs are guaranteed to withstand severe test
programs
• Long-life cycle tests (over 5000 trip cycles)
• Long-life storage tests (3000 h at 250 °C)
• Electrical cycle tests at low ambient temperatures
(-40 °C or 0 °C)
• Damp-heat and water immersion tests
• Overvoltage tests at up to 200 % of rated voltage
FEATURES
• Wide range of trip and non-trip currents:
From 11 mA up to 800 mA
• Small ratio between trip and non-trip currents
(It/Int = 1.5 at 25 °C)
• High maximum inrush current (up to 5.5 A)
• Leaded parts withstand mechanical stresses
and vibration
• UL file E148885 according to XGPU standard UL1434
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
Overload (current, voltage, temperature) protection in:
• Industrial electronics
• Consumer electronics
• Electronic data processing
DESCRIPTION
These directly heated ceramic-based thermistors have a
positive temperature coefficient and are primarily intended
for overload protection. They consist of a ceramic pellet
soldered between two tinned CCS wires and coated with a
UL 94 V-0 high temperature hard silicone lacquer.
MOUNTING
PTC thermistors can be mounted by wave, reflow, or
hand-soldering. Current levels have been determined
according IEC 60738 conditions. Different ways of
mounting or connecting the thermistors can influence their
thermal and electrical behavior. Standard operation is in still
air, any potting or encapsulation of PTC thermistors is not
recommended and will change its operating characteristics.
Typical Soldering
235 °C; duration: 5 s (Lead (Pb)-bearing)
245 °C, duration: 5 s (Lead (Pb)-free)
Resistance to Soldering Heat
260 °C, duration: 10 s max.
MARKING
Only the gray lacquered thermistors with a diameter of
8.5 mm to 20.5 mm are marked with BC, R25 value (example
1R9) on one side and Int, Vmax. on the other side.
Revision: 21-Sep-15
1 Document Number: 29087
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1 page  
www.vishay.com
TYPICAL RESISTANCE / TEMPERATURE
CHARACTERISTIC
108
107 PTCCL05H110HBE
PTCCL05H150HBE
106
105
PTCCL05H190HBE
104
103 PTCCL05H280HBE
102
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
TYPICAL RESISTANCE / TEMPERATURE
CHARACTERISTIC
108
107
106
PTCCL05H390HBE
105
PTCCL05H630HBE
104
PTCCL05H760HBE
103
102
PTCCL05H950HBE
10
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
PTCCL - 265 V Series
Vishay BCcomponents
TYPICAL RESISTANCE / TEMPERATURE
CHARACTERISTIC
106
105 PTCCL11H211HBE
104 PTCCL11H251HBE
103
PTCCL13H281HBE
102
10 PTCCL13H321HBE
1
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
TYPICAL RESISTANCE / TEMPERATURE
CHARACTERISTIC
106
105
104
103
102
PTCCL17H401HBE
10
PTCCL17H491HBE
1
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
TYPICAL RESISTANCE / TEMPERATURE
CHARACTERISTIC
107
106
PTCCL07H111HBE
105
PTCCL07H141HBE
104
103
PTCCL09H171HBE
102
10 PTCCL09H191HBE
1
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
TYPICAL RESISTANCE / TEMPERATURE
CHARACTERISTIC
106
105
104 PTCCL21H591HBE
103
PTCCL21H701HBE
102
10
PTCCL21H801HBE
1
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
Revision: 21-Sep-15
5 Document Number: 29087
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet PTCCL05H150HTE.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PTCCL05H150HTE | 265 V PTC Thermistors | Vishay |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |