DataSheet.jp

ST950-30L2MI の電気的特性と機能

ST950-30L2MIのメーカーはVishayです、この部品の機能は「Wet Tantalum Capacitors」です。


製品の詳細 ( Datasheet PDF )

部品番号 ST950-30L2MI
部品説明 Wet Tantalum Capacitors
メーカ Vishay
ロゴ Vishay ロゴ 




このページの下部にプレビューとST950-30L2MIダウンロード(pdfファイル)リンクがあります。

Total 6 pages

No Preview Available !

ST950-30L2MI Datasheet, ST950-30L2MI PDF,ピン配置, 機能
www.vishay.com
ST
Vishay
SuperTan® Wet Tantalum Capacitors
with Hermetic Seal
Vishay ST represents a major breakthrough in wet tantalum
capacitor technology. Its unique cathode system provides
the highest capacitance per unit volume. The design
facilitates a doubling of capacitance, lower ESR and higher
ripple current rating compared with conventional wet
tantalum products. Moreover, the ST has the capacitance
stability of a solid tantalum capacitor and there are no circuit
impedance restrictions.
The ST is housed in an all tantalum, hermetically sealed case
and is manufactured to withstand hazardous environments.
The ST is used widely in the defense and aerospace
industries and whenever there is a space problem.
PERFORMANCE CHARACTERISTICS
Operating Temperature: -55 °C to +85 °C
(to +125 °C with voltage derating)
Capacitance Tolerance: at 120 Hz, +25 °C.
± 20 % standard. ± 10 % available as special.
FEATURES
• Very high capacitance
• 10 μF to 1800 μF
• 25 VDC to 125 VDC
• Very low ESR
• High ripple current
• All tantalum case
• Hermetically sealed
• Low DCL
Available
Available
• Axial through-hole terminations: standard tin / lead (Sn / Pb),
100 % tin (RoHS-compliant) available
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Note
* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details.
APPLICATION NOTES
a. No continuous reverse voltage permissible.
b. The peak of the applied AC ripple and the applied DC
voltage must not exceed the DC voltage rating of the
capacitor.
c. Ripple current ratings by part number at 85 °C and
40 kHz are included in the table. Ripple current correction
factors for other temperatures and frequencies are given
on the next page.
d. Transient reverse voltage surges are acceptable under
the following conditions:
the peak reverse voltage does not exceed 1.5 V and the
peak current times the duration of the reverse transient
does not exceed 0.05 As. In addition, the repetition
frequency of the reverse voltage surge is less than 10 Hz.
DIMENSIONS in inches [millimeters]
Terminal welded
to case
0.250 [6.35]
MAX.
0.0253 ± 0.002 [0.64 ± 0.05] dia.
(no. 22 AWG) tinned nickel leads
solderable and weldable
0.094 [2.38]
MAX.
E
L1
E
CASE CODE
D ± 0.016 [0.41]
MAX. INSULATED
(DIA.)
T1 0.188 [4.78] 0.219 [5.56]
T2 0.281 [7.14] 0.312 [7.92]
L2 0.281 [7.14] 0.312 [7.92]
T3
0.375 [9.52]
0.406 [10.31]
T4
0.375 [9.52]
0.406 [10.31]
Notes
• Material at egress is Tantalum
• Insulation sleeving will lap over the ends of the capacitor case
“D” DIA.
L1 + 0.031 / - 0.016 [+ 0.79 / - 0.41]
UNINSULATED
0.453 [11.51]
0.641 [16.28]
1.008 [25.60]
0.766 [19.46]
1.062 [26.97]
Terminal location
within 0.031 of center
E ± 0.250 [6.3] MAX.
1.500 [38.10]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
• Approx. weight:
T1: 2.3 g, T2: 5.7 g,
T3: 9.4 g, T4: 14.8 g
Revision: 06-Jul-15
1 Document Number: 43000
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

1 Page





ST950-30L2MI pdf, ピン配列
www.vishay.com
ST
Vishay
STANDARD RATINGS
CAPACITANCE
AT 25 °C
AND 120 Hz
(μF)
CASE
CODE
MAX.
ESR
120 Hz
(Ω)
MAX. DCL AT
+25 °C
(μA)
+85 °C /
+125 °C
(μA)
MAX. IMP.
AT -55 °C
AND 120 Hz
(Ω)
MAX. CAPACITANCE
CHANGE AT
-55 °C +85 °C +125 °C
(%) (%) (%)
AC RIPPLE
85 °C
40 kHz
(mA)
RMS
PART NUMBER
100 VDC AT 85 °C; 65 VDC AT 125 °C
15
T1 3.5
1
5
125
-18 +3 +10
1050
ST15-100T1MI
68
T2 2.1
2
10
37
-30 +4 +12
1650
ST68-100T2MI
120
L2 1.0
3
25
20.5
-30 +4 +12
2200
ST120-100L2MI
150
T3 1.6
3
25
22
-35 +6 +12
2100
ST150-100T3MI
220
T4 1.2
5
50
15
-40 +6 +12
2750
ST220-100T4MI
125 VDC AT 85 °C; 85 VDC AT 125 °C
10
T1 5.5
1
5
175
-15 +3 +10
1050
ST10-125T1MI
47
T2 2.3
2
10
47
-25 +5 +12
1650
ST47-125T2MI
90
L2 1.3
5
25
25
-22 +4 +15
2000
ST90-125L2MI
82
T3 1.8
3
25
40
-35 +5 +12
1950
ST82-125T3MI
100
T3 1.8
3
25
35
-35 +5 +12
2100
ST100-125T3MI
150
T4 1.6
5
50
20
-35 +6 +12
2750
ST150-125T4MI
Notes
• (K = ± 10 %, M = ± 20 %) and insulation letter (I = insulation, X = uninsulated)
• Part numbers shown are for units with ± 20 % capacitance tolerance and uninsulated capacitors. For ± 10 units, change the digit following
the letter “X” from “0” to “9”. For units with outer plastic-film insulation, substitute “2” for “0” at the end of the part number
• For RoHS-compliant add “E3” for suffix
RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE, AND APPLIES PEAK VOLTAGE
FREQUENCY
OF APPLIED
RIPPLE
CURRENT
120 Hz
800 Hz
1 kHz
10 kHz
40 kHz
100 kHz
AMBIENT STILL
AIR TEMP. IN °C
55
85
105 125 55
85
105 125 55
85
105 125 55
85
105 125 55 85
105 125 55 85
105 125
100 % 0.60 0.39 - - 0.71 0.43 - - 0.72 0.46 - - 0.88 0.55 - - 1.0 0.63 - - 1.1 0.69 - -
% of 90 % 0.60 0.46 - - 0.71 0.55 - - 0.72 0.55 - - 0.88 0.67 - - 1.0 0.77 - - 1.1 0.85 - -
85 °C
rated 80 % 0.60 0.52 0.35 - 0.71 0.62 0.42 - 0.72 0.62 0.42 - 0.88 0.76 0.52 - 1.0 0.87 0.59 - 1.1 0.96 0.65 -
peak
voltage 70 % 0.60 0.58 0.44 - 0.71 0.69 0.52 - 0.72 0.70 0.52 - 0.88 0.85 0.64 - 1.0 0.97 0.73 - 1.1 1.07 0.80 -
66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50
Revision: 06-Jul-15
3 Document Number: 43000
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


3Pages


ST950-30L2MI 電子部品, 半導体
www.vishay.com
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Revision: 13-Jun-16
1 Document Number: 91000

6 Page



ページ 合計 : 6 ページ
 
PDF
ダウンロード
[ ST950-30L2MI データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ST950-30L2MI

Wet Tantalum Capacitors

Vishay
Vishay


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap