DataSheet.jp

DTA143ZEFRA の電気的特性と機能

DTA143ZEFRAのメーカーはROHM Semiconductorです、この部品の機能は「PNP Digital Transistor」です。


製品の詳細 ( Datasheet PDF )

部品番号 DTA143ZEFRA
部品説明 PNP Digital Transistor
メーカ ROHM Semiconductor
ロゴ ROHM Semiconductor ロゴ 




このページの下部にプレビューとDTA143ZEFRAダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

DTA143ZEFRA Datasheet, DTA143ZEFRA PDF,ピン配置, 機能
DTA143ZE FRA
PNP -100mA -50V Digital Transistor (Bias Resistor Built-in Transistor)
Datasheet
AEC-Q101 Qualified
Parameter
VCC
IC(MAX.)
R1
R2
Value
-50V
-100mA
4.7kΩ
47kΩ
lFeatures
1) Built-In Biasing Resistors, R1 = 4.7kΩ, R2 = 47kΩ
2) Built-in bias resistors enable the configuration of
 an inverter circuit without connecting external
 input resistors (see inner circuit) .
3) Only the on/off conditions need to be set
 for operation, making the circuit design easy.
4) Complementary NPN Types: DTC143ZE FRA
lOutline
SOT-416
 
SC-75A
 
 
 
  
(EMT3)
 
              
lInner circuit
lApplication
INVERTER, INTERFACE, DRIVER
lPackaging specifications
Part No.
Package
Package
size
                      
Taping
code
Reel size Tape width
(mm) (mm)
Basic
ordering
unit.(pcs)
Marking
DTA143ZE FRA SOT-416 1616
TL
180
8
(EMT3)
3000
E13
                                                                                        
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
1/5
20161011 - Rev.001

1 Page





DTA143ZEFRA pdf, ピン配列
DTA143ZE FRA
 
lElectrical characteristic curves (Ta =25°C)
 
        
Datasheet
Fig.1 Input voltage vs. output current (ON
characteristics)
Fig.2 Output current vs. input voltage (OFF
characteristics)
Fig.3 Output current vs. output voltage
Fig.4 DC current gain vs. output current
                                                                                          
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
3/5
20161011 - Rev.001


3Pages


DTA143ZEFRA 電子部品, 半導体
Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (Specific Applications), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHMs Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU CHINA
CLASS
CLASS
CLASS
CLASSb
CLASS
CLASS
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ DTA143ZEFRA データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
DTA143ZEFRA

PNP Digital Transistor

ROHM Semiconductor
ROHM Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap