DataSheet.jp

AM2LW-NZ の電気的特性と機能

AM2LW-NZのメーカーはAIMTECです、この部品の機能は「DC-DC Converter」です。


製品の詳細 ( Datasheet PDF )

部品番号 AM2LW-NZ
部品説明 DC-DC Converter
メーカ AIMTEC
ロゴ AIMTEC ロゴ 




このページの下部にプレビューとAM2LW-NZダウンロード(pdfファイル)リンクがあります。
Total 3 pages

No Preview Available !

AM2LW-NZ Datasheet, AM2LW-NZ PDF,ピン配置, 機能
FEATURES:
SMD package
Ultra Wide (4:1) input range
1500VDC isolation
Continuous short circuit
protection
Click on Series name for product info on aimtec.com
Series AM2LW-NZ
1.5 Watt | DC-DC Converter
Operating temperature: -40°C to +85°C
Regulated single/dual output
MTBF>1,000,000 hours
RoHS compliant
Models: Single output
Model
Input Voltage(V)
AM2LW-2403S-NZ
AM2LW-2405S-NZ
AM2LW-2409S-NZ
AM2LW-2412S-NZ
AM2LW-2415S-NZ
AM2LW-4805S-NZ
9-36
9-36
9-36
9-36
9-36
18-72
Output Voltage
(V)
3.3
5
9
12
15
5
Output Current
max(mA)
455
300
167
125
100
300
Isolation
(VDC)
1500
1500
1500
1500
1500
1500
Efficiency
(%)
72
76
78
79
80
76
Models: Dual output
Model
Input Voltage
(V)
AM2LW-2405D-NZ
9-36
AM2LW-2412D-NZ
9-36
AM2LW-2415D-NZ
9-36
Output Voltage
(V)
±5
±12
±15
Output Current
max (mA)
±150
±63
±50
Isolation
(VDC)
1500
1500
1500
Efficiency
(%)
74
77
75
NOTE 1: Add suffix “TR” to a part number when ordering in tape and reel package
NOTE 2: Unless otherwise specified, all specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load.
Input Specifications
Parameters
Voltage range
Absolute Maximum Rating
Peak Input Voltage time
Nominal
24
48
24
48
Typical
9-36
18-72
Maximum
40
80
100
Units
VDC
VDC
ms
Isolation Specifications
Parameters
Tested I/O voltage
Resistance
Capacitance
Conditions
60 sec
At 500 Vdc
Input to Output
Typical
1000
1000
Rated
1500
Units
VDC
MOhm
pF
Output Specifications
Parameters
Conditions
Typical
Voltage accuracy
±5
Short Circuit protection
Continuous
Short circuit restart
Auto-Recovery
Line voltage regulation
From Low in to High In
±0.75
Load voltage regulation (Single)
From 10% to 100% load
±1.5
Load voltage regulation (Dual)
From 10% to 100% load
Unbalanced load
±5
Temperature coefficient
±0.03
Ripple & Noise
20MHz Bandwidth
100
Minimum Load Current*
10
* Operation under 10% load will not damage the converter; however, not all specifications will be met.
www.aimtec.com
Tel: +1 514 620 2722
F 051e R8.G
1 of 3
Maximum
Units
%
%
%
%
%/oC
mV p-p
% of Max
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only

1 Page





AM2LW-NZ pdf, ピン配列
Recommended Filter Circuit
+ Vin
Cin +
Dual Output
Cout +
DC DC Cout +
- Vin
+Vout
Common
+ Vin
Cin +
-Vout
- Vin
Series AM2LW-NZ
1.5 Watt | DC-DC Converter
Single Output
+Vout
Cout +
DC DC
- Vout
All the AM2LW-Z Series have been tested with the above recommended test circuit. This series should be tested under load.
If it is necessary to further decrease the input/output ripple, the value of the filter capacitor can be increased; a capacitor with a low ESR
should be used. Excessive filter capacitance can cause start up problems with the converter.
In general, the recommended capacitance values are:
Cin: 10μF~47μF
Cout: 10μF/100mA
Refer to table below for maximum capacitor values:
External Capacitor Value
Single Output
Vout (VDC)
5
12
15
Cout (uF)
1000
470
330
Dual Output
Vout (VDC)
±5
±12
±15
Cout (uF)
±680
±330
±220
Derating
Free Air Convection
100
80
Safe Operating Area
60
40
71ºC
20
0
- 40 - 20
0
20 40 60 80 85 100
Ambient Temperature º C
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R8.G
Tel: +1 514 620 2722
3 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ AM2LW-NZ データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
AM2LW-NZ

DC-DC Converter

AIMTEC
AIMTEC


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap