|
|
Número de pieza | USB84604 | |
Descripción | USB 2.0 HSIC Hi-Speed 4-Port Controller Hub | |
Fabricantes | Microchip | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de USB84604 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! USB84604
USB 2.0 HSIC Hi-Speed 4-Port Controller Hub
Highlights
• Controller Hub IC with 4 downstream ports
• High-Speed Inter-Chip (HSIC) support
- Upstream port selectable between HSIC or
USB 2.0
• USB-IF Battery Charger revision 1.2 support on
downstream ports (DCP, CDP, SDP)
• Battery charging support for Apple® devices
• FlexConnect: Downstream port 1 able to swap
with upstream port, allowing master capable
devices to control other devices on the hub
• USB to I2CTM/SPI/GPIO/UART bridge support
through the Hub Controller
• Device functionality and configuration for USB
host/slave swapping is also provided by external
SPI Flash
• USB Link Power Management (LPM) support
• SUSPEND pin for remote wakeup indication to
host
• Start Of Frame (SOF) synchronized clock output
pin
• Vendor Specific Messaging (VSM) support
• Enhanced OEM configuration options available
through OTP or SMBus Slave Port
• Flexible power rail support
- VBUS or VBAT only operation
- 3.3 V only operation
- VBAT + 1.8 V operation
- 3.3 V + 1.8 V operation
• 48-pin (7x7 mm) QFN RoHS compliant package
Target Applications
• Automotive head unit
• Automotive breakout box
• Navigation devices
• Automotive consumer connectivity ports
• Smart phones requiring host and device modes
• Rear seat infotainment access
Key Benefits
• MultiTRAKTM
- Dedicated Transaction Translator per port
• PortMap
- Configurable port mapping and disable
sequencing
• PortSwap
- Configurable differential intra-pair signal
swapping
• PHYBoostTM
- Programmable USB transceiver drive
strength for recovering signal integrity
• VariSenseTM
- Programmable USB receiver sensitivity
• Low power operation
• Full Power Management with individual or ganged
power control of each downstream port
• Built-in Self-Powered or Bus-Powered internal
default settings provide flexibility in the quantity of
USB expansion ports utilized without redesign
• Supports OTP configurable flash
• Fully integrated USB termination and Pull-up/Pull-
down resistors
• On-chip Power On Reset (POR)
• Internal 3.3 V and 1.2 V voltage regulators
• On Board 24 MHz Crystal Driver, Resonator, or
External 24 MHz clock input
• Temperature range: -40 ºC to 85 ºC
2014-2016 Microchip Technology Inc.
DS60001295C-page 1
1 page USB84604
The Hub Feature Controller adds advanced functionality to the USB84604 by enabling the host to send commands
directly to it via the upstream USB connection. The Hub Feature Controller includes a USB peripheral/slave controller
that receives commands which are contained in the USB data packet. The following functions can be controlled via com-
mands through the Hub Feature Controller:
• I2C over USB Bridging: The host can send commands through USB to any device connected to the hub through
the SMBus.
• UART over USB Bridging: The host can send commands through USB to any device connected to the hub
through the UART. For more details about UART functions refer to the SDK.
• SPI over USB Bridging: The host accesses to an attached SPI device as a pass-through operation.
• GPIO Control: The GPIOs on the hub can be dynamically configured and controlled by the host. For more details
about GPIO functions refer to the SDK.
• OTP Programming: Permanent customer configurations can be loaded to the One Time Programmable memory.
• FlexConnect support: FlexConnect allows the hub to dynamically change the physical ports that act as upstream
and downstream ports. For more details refer to the FlexConnect Applications [ 9].
• Access to configuration registers
2014-2016 Microchip Technology Inc.
DS60001295C-page 5
5 Page USB84604
TABLE 3-1: PIN DESCRIPTIONS (CONTINUED)
Num Pins
Name
1 Downstream
USB D+
(Port 3)
Port 3 D+
Disable
Configuration
Strap
Symbol
USBDN3_DP
PRT_DIS_P3
1
Downstream
USBDN3_DM
USB D-
(Port 3)
Port 3 D-
Disable
Configuration
Strap
PRT_DIS_M3
1
Downstream
USBDN4_DP
USB D+
(Port 4)
Port 4 D+
Disable
Configuration
Strap
PRT_DIS_P4
Buffer
Type
AIO
Description
Downstream USB Port 3 D+ data signal.
IS This strap is used in conjunction with
PRT_DIS_M3 to disable USB Port 3.
0 = Port 3 D+ Enabled
1 = Port 3 D+ Disabled
Note:
Both PRT_DIS_P3 and PRT_DIS_M3
must be tied to VDD33 at reset to dis-
able the associated port.
See Note 2 for more information on configuration
straps.
AIO Downstream USB Port 3 D- data signal.
IS This strap is used in conjunction with
PRT_DIS_P3 to disable USB Port 3.
0 = Port 3 D- Enabled
1 = Port 3 D- Disabled
Note:
Both PRT_DIS_P3 and PRT_DIS_M3
must be tied to VDD33 at reset to dis-
able the associated port.
See Note 2 for more information on configuration
straps.
AIO Downstream USB Port 4 D+ data signal.
IS This strap is used in conjunction with
PRT_DIS_M4 to disable USB Port 4.
0 = Port 4 D+ Enabled
1 = Port 4 D+ Disabled
Note:
Both PRT_DIS_P4 and PRT_DIS_M4
must be tied to VDD33 at reset to dis-
able the associated port.
See Note 2 for more information on configuration
straps.
2014-2016 Microchip Technology Inc.
DS60001295C-page 11
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet USB84604.PDF ] |
Número de pieza | Descripción | Fabricantes |
USB84604 | USB 2.0 HSIC Hi-Speed 4-Port Controller Hub | Microchip |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |