DataSheet.jp

2016L100 の電気的特性と機能

2016L100のメーカーはLittelfuseです、この部品の機能は「Resettable PTC」です。


製品の詳細 ( Datasheet PDF )

部品番号 2016L100
部品説明 Resettable PTC
メーカ Littelfuse
ロゴ Littelfuse ロゴ 




このページの下部にプレビューと2016L100ダウンロード(pdfファイル)リンクがあります。

Total 5 pages

No Preview Available !

2016L100 Datasheet, 2016L100 PDF,ピン配置, 機能
POLY-FUSE® Resettable PTCs
Surface Mount > 2016L Series
2016L Series
RoHS
Agency Approvals
AGENCY
AGENCY FILE NUMBER
E183209
R50119118
Description
The 2016L Series PTC provides surface mount overcurrent
protection for low voltage (≤60V) applications where
resettable protection is desired.
Features
• RoHS compliant, lead-free
and halogen-free
• Fast response to fault
currents
• High voltage
• Low-profile
Applications
• IEEE 1394 port protection
• P owered ethernet port
protection (IEEE 802.3 af)
• Automotive electronic
control module protection
• Low voltage telecom
equipment protection
Electrical Characteristics
Part Number
Marking
I hold
(A)
I trip
V max
(A) (Vdc)
Maximum Time
I max
(A)
P d(Wty)p.
To Trip
Current Time
(A) (Sec.)
Resistance
R min
(Ω)
R 1max
(Ω)
Agency
Approvals
2016L030
LF030 0.30 0.60
60
20 1.40
1.5
3.0
0.500 2.300
X
X
2016L050
LF050 0.55 1.10
60
20 1.40
2.5
5.0 0.200 1.000 X
X
2016L075/60 LF075-60 0.75 1.50
60
20 1.40
8.0
0.5
0.130 0.900
X
X
2016L100
LF100 1.10 2.20
15
40 1.40
8.0
0.5
0.100 0.400
X
X
2016L100/33 LF100-33 1.10 2.20
33
40 1.40
8.0
0.5
0.100 0.400
X
X
2016L150
LF150 1.50 3.00
15
40 1.40
8.0
1.0
0.070 0.180
X
X
2016L150/33 LF150-33 1.50 3.00
33
40 2.0 8.00
1.00 0.070 0.180
2016L200
LF200 2.00 4.20
6
40 1.40
8.0
3.0
0.048 0.100
X
X
2016L260/24 LF260-24 2.60 5.00
24
40 1.6 8.00
5.00 0.025 0.075
2016L300/16 LF0300 3.00 5.00
16
40
1.6
8.00
10.00
0.015 0.048
2016L500
LF500 5.00 10.00
6
100 2.0 25.00
2.00 0.005 0.025
X
I hold = Hold current: maximum current device will pass without tripping in 20°C still air.
I trip = Trip current: minimum current at which the device will trip in 20°C still air.
V max = Maximum voltage device can withstand without damage at rated current (I max)
I max = Maximum fault current device can withstand without damage at rated voltage (Vmax)
P d = Power dissipated from device when in the tripped state at 20°C still air.
R min = Minimum resistance of device in initial (un-soldered) state.
R typ = Typical resistance of device in initial (un-soldered) state.
R 1max = M aximum resistance of device at 20°C measured one hour after tripping or reflow soldering of 260°C for 20 sec.
Caution: Operation beyond the specified rating may result in damage and possible arcing and flame.
* Agency Approval is Pending
WARNING
• Users shall independently assess the suitability of these devices for each of their applications
• Operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or fire
• These devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such
conditions are expected to be repetitive or prolonged in duration
• Exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these PPTC devices
• These devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses
• Circuits with inductance may generate a voltage (L di/dt) above the rated voltage of the PPTC device.
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 08/22/16

1 Page





2016L100 pdf, ピン配列
POLY-FUSE® Resettable PTCs
Surface Mount > 2016L Series
Soldering Parameters
Profile Feature
Pb-Free Assembly
Average Ramp-Up Rate (TS(max) to TP)
Temperature Min (Ts(min))
Pre Heat:
Temperature Max (Ts(max))
Time (Min to Max) (ts)
Time Maintained Temperature (TL)
Above:
Temperature (tL)
Peak / Classification Temperature (TP)
Time within 5°C of actual peak
Temperature (tp)
Ramp-down Rate
Time 25°C to peak Temperature (TP)
3°C/second max
150°C
200°C
60 – 180 secs
217°C
60 – 150 seconds
260+0/-5 °C
20 – 40 seconds
6°C/second max
8 minutes Max.
Physical Specifications
Terminal Material
Solder-Plated Copper (Solder Material:
Matte Tin(Sn))
Lead Solderability
Meets EIA Specification RS186-9E, ANSI/
J-STD-002 Category 3.
TP
TL
TS(max)
TS(min)
Ramp-up
Preheat
tS
tP
Critical Zone
tL to tP
tL
Ramp-down
25
time to peak temperature
Time
-- All temperature refer to topside of the package, measured on the package body surface
-- If reflow temperature exceeds the recommended profile, devices may not meet the
performance requirements
--
Recommended
for lead
reflow
methods:
IR,
vapor
phase
oven,
hot
air
oven,
N2
environment
-- Recommended maximum paste thickness is 0.25mm(0.010inch)
-- Devices can be cleaned usingstandard industry methods and solvents
-- Devices can be reworked using the standard industry practices
Environmental Specifications
Operating/Storage
Temperature
Maximum Device Surface
Temperature in Tripped
State
Passive Aging
Humidity Aging
Thermal Shock
Solvent Resistance
Vibration
-40°C to +85°C
125°C
+85°C, 1000 hours
-/+5% typical resistance change
+85°C, 85%,R.H.,1000 hours
-/+5% typical resistance change
MIL–STD–202, Method 107
+85°C/-40°C 20 times
-30% typical resistance change
MIL–STD–202, Method 215
No change
MIL–STD–883, Method 2007,
Condition A
No change
Moisture Sensitivity Level Level 1, J–STD–020
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 08/22/16


3Pages





ページ 合計 : 5 ページ
 
PDF
ダウンロード
[ 2016L100 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
2016L100

Resettable PTC

Littelfuse
Littelfuse


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap