DataSheet.jp

HV219 の電気的特性と機能

HV219のメーカーはSupertexです、この部品の機能は「8-Channel High Voltage Analog Switch」です。


製品の詳細 ( Datasheet PDF )

部品番号 HV219
部品説明 8-Channel High Voltage Analog Switch
メーカ Supertex
ロゴ Supertex ロゴ 




このページの下部にプレビューとHV219ダウンロード(pdfファイル)リンクがあります。

Total 9 pages

No Preview Available !

HV219 Datasheet, HV219 PDF,ピン配置, 機能
Supertex inc.
HV219
200V Low Charge Injection
8-Channel High Voltage Analog Switch
Features
►HVCMOS® technology for high performance
►Very low quiescent power dissipation (-10µA)
Output on-resistance typically 11Ω
►Low parasitic capacitance
►DC to 50MHz small signal frequency response
►-60dB typical off-isolation at 5.0MHz
►CMOS logic circuitry for low power
►Excellent noise immunity
►Serial shift register logic control with latches
►Flexible operating supply voltages
►Surface mount packages
Applications
►Medical ultrasound imaging
►Non-destructive evaluation
General Description
The Supertex HV219 is a low switch resistance, low charge
injection, 8-channel, 200V, analog switch integrated circuit (IC)
intended primarily for medical ultrasound imaging. The device can
also be used for NDE (non-destructive evaluation) applications. The
HV219 is a lower switch resistance, 11Ω versus 22Ω, version of the
Supertex HV20220 device. The lower switch resistance will help
reduce insertion loss. It has the same pin configuration as that of the
Supertex HV20220PJ and the HV20220FG.
The device is manufactured using Supertex’s HVCMOS® (high
voltage CMOS) technology with high voltage bilateral DMOS
structures for the outputs and low voltage CMOS logic for the input
control. The outputs are configured as eight independent single
pole single throw 11Ω analog switches. The input logic is an 8-bit
serial to parallel shift register followed by an 8-bit parallel latch. The
switch states are determined by the data in the latch. Logic high will
correspond to a closed switch and logic low as an opened switch.
Block Diagram
The HV219 is designed to operate on various combinations of high
voltage supplies. For example the VPP and VNN supplies can be:
+40V/-160V, +100V/-100V, or +160V/-40V. This allows the user to
maximize the signal voltage for uni-polar negative, bi-polar, or uni-
polar positive.
DIN
CLK
DOUT
8-Bit
Shift
Register
Level Output
Latches Shifters Switches
D
LE
CL
D
LE
CL
D
LE
CL
D
LE
CL
D
LE
CL
D
LE
CL
D
LE
CL
D
LE
CL
SW0
SW1
SW2
SW3
SW4
SW5
SW6
SW7
Doc.# DSFP-HV219
C070713
VDD GND LE CL
VNN VPP
Supertex inc.
www.supertex.com

1 Page





HV219 pdf, ピン配列
HV219
DC Electrical Characteristics (over recommended operating conditions unless otherwise noted)
Sym Parameter
0OC
+25OC
+70OC
Units Conditions
Min Max Min Typ Max Min Max
RONS
Small signal switch
on-resistance
ΔRONS
RONL
Small signal switch
on-resistance matching
Large signal switch
on-resistance
- 15 - 13 19 - 24
- 13 - 11 14 - 16
ISIG = 5.0mA VPP = +40V
ISIG = 200mA VNN = -160V
-
-
13
9.0
-
-
11 14
9.0 12
-
-
15
14
Ω
ISIG = 5.0mA VPP = +100V
ISIG = 200mA VNN = -100V
- 12 - 10 13 - 15
- 11 -
8 13 - 14
ISIG = 5.0mA VPP= +160V
ISIG = 200mA VNN = -40V
-
20
-
5.0 20
-
20
%
ISIG = 5.0mA, VPP = +100V,
VNN = -100V
- - - 8.0 - - - Ω VSIG = VPP -10V, ISIG = 1.0A
ISOL Switch off leakage per switch - 5.0 - 1.0 10 - 15 µA VSIG = VPP -10V & VNN +10V
DC offset switch off
VOS DC offset switch on
- 300 - 100 300 - 300 mV RLOAD = 100kΩ
- 500 - 100 500 - 500 mV RLOAD = 100kΩ
IPPQ Quiescent VPP supply current - - - 10 50 - - µA All switches off
INNQ Quiescent VNN supply current - - - -10 -50 - - µA All switches off
IPPQ Quiescent VPP supply current -
-
- 10 50 -
-
µA
All switches on,
ISW = 5.0mA
INNQ Quiescent VNN supply current -
-
- -10 -50 -
-
µA
All switches on,
ISW = 5.0mA
ISW Switch output peak current
- 3.0 - 3.0 2.0 - 2.0 A VSIG duty cycle < 0.1%
fSW Output switch frequency
- - - - 50 - - kHz Duty cycle = 50%
IPP Average VPP supply current
INN Average VNN supply current
- 6.5 -
- 4.0 -
- 4.0 -
- 6.5 -
- 4.0 -
- 4.0 -
- 7.0 - 8.0
VPP = +40V
VNN = -160V
All output
switches
-
5.0
-
5.5
mA
VPP = +100V
VNN = -100V
are turning
on and off
- 5.0 - 5.5
VPP = +160V
VNN = -40V
at 50kHz
with no load
- 7.0 - 8.0
VPP = +40V
VNN = -160V
All output
switches
-
5.0
-
5.5
mA
VPP = +100V
VNN = -100V
are turning
on and off
- 5.0 - 5.5
VPP = +160V
VNN = -40V
at 50kHz
with no load
IDD Average VDD supply current
- 4.0 -
- 4.0 - 4.0 mA fCLK = 5.0MHz, VDD = 5.0V
IDDQ Quiescent VDD supply current - 10 -
- 10 - 10 µA All logic inputs are static
ISOR Data out source current
0.45 - 0.45 0.70 - 0.40 -
mA VOUT = VDD -0.7V
ISINK Data out sink current
0.45 - 0.45 0.70 - 0.40 - mA VOUT = 0.7V
CIN Large input capacitance
- 10 -
- 10 - 10 pF ---
Doc.# DSFP-HV219
C070713
Supertex inc.
3 www.supertex.com


3Pages


HV219 電子部品, 半導体
Test Circuits
VPP - 10V
ISOL
VNN + 10V
VOUT
RLOAD
100kΩ
VPP -10V
RLOAD
10kΩ
VOUT
HV219
VPP VPP
VNN VNN
VDD
GND
5V
Switch OFF Leakage
VPP VPP
VNN VNN
VDD
GND
5V
DC Offset ON/OFF
VPP VPP
VNN VNN
VDD
GND
5V
TON/TOFF Test Circuit
VIN = 10VP-P
@5.0MHz
VOUT
RLOAD
VSIG
IID
VNN
VIN = 10VP-P
@5.0MHz
50Ω
50Ω
NC
VPP VPP
VNN VNN
VDD
GND
5V
KO
=
20
Log
VOUT
VIN
OFF Isolation
VPP VPP
VNN VNN
VDD
GND
5V
Isolation Diode Current
VPP VPP
VNN VNN
VDD
GND
5V
KCR
=
20Log
VOUT
VIN
Crosstalk
VOUT
VOUT
1000pF
VSIG
+VSPK
-VSPK
VOUT
RLOAD
50Ω
1.0KΩ
VPP VPP
VNN VNN
VDD
GND
5V
VPP VPP
VNN VNN
VDD
GND
5V
Q = 1000pF x VOUT
Charge Injection
Output Voltage Spike
Doc.# DSFP-HV219
C070713
Supertex inc.
6 www.supertex.com

6 Page



ページ 合計 : 9 ページ
 
PDF
ダウンロード
[ HV219 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HV214

High Voltage Analog Switch

Supertex  Inc
Supertex Inc
HV214FG

High Voltage Analog Switch

Supertex  Inc
Supertex Inc
HV214FG-G

High Voltage Analog Switch

Supertex
Supertex
HV214PJ

High Voltage Analog Switch

Supertex  Inc
Supertex Inc


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap