|
|
PDF IRU1176 Data sheet ( Hoja de datos )
| Número de pieza | IRU1176 | |
| Descripción | 7.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR | |
| Fabricantes | International Rectifier | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IRU1176 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Data Sheet No. PD94132
IRU1176
7.5A ULTRA LOW DROPOUT POSITIVE
ADJUSTABLE REGULATOR WITH SHUTDOWN INPUT
FEATURES
Guaranteed <0.65V Dropout at 7.5A
Fast Transient Response
1% Voltage Reference Initial Accuracy
Built-In Thermal Shutdown
APPLICATIONS
3.3V to 2.7V Intel I740 Chip Set
DESCRIPTION
The IRU1176 is a 7.5A regulator with extremely low drop-
out voltage using a proprietary Bipolar process that
achieves comparable equivalent on resistance to that of
discrete MOSFETs. The IRU1176 also provides a conve-
nient shutdown pin that allows the regulator to be shut-
down and reduce the input current consumption. Unlike
the PNP type regulators this device does not have high
quiescent current during the start up mode making it
ideal for applications where there is limited current ca-
pability such operation from the 5V standby supply of
the computer power supply. One application is the new
generation of RDRAM memory that needs to provide 2.5V
from 3.3V input and be able to operate from 5VSB as
well.
TYPICAL APPLICATION
3.3V
C1
IRU1176
VIN 7
VIN 6
VCTRL 5
VOUT 4
Adj 3
SD 2
VSENSE 1
5V
C2 Q1
2.7V
R1
C3
R2
SD Enable
Figure 1 - Typical application of IRU1176.
PACKAGE ORDER INFORMATION
TJ (°C)
0 To 125
7-PIN PLASTIC
TO-263 (M)
IRU1176CM
7-PIN PLASTIC
Ultra Thin-PakTM (P)
IRU1176CP
Rev. 1.5
07/16/02
www.irf.com
1
1 page  
IRU1176
The IRU1176 keeps a constant 1.25V between the VSENSE
pin and the VADJ pin. By placing a resistor R1 across
these two pins and connecting the VSENSE and VOUT pin
together, a constant current flows through R1, adding to
the IADJ current and into the R2 resistor producing a volt-
age equal to the (1.25/R1)3R2 + IADJ3R2. This voltage
is then added to the 1.25V to set the output voltage.
This is summarized in the above equation. Since the
minimum load current requirement of the IRU1176 is
10mA, R1 is typically selected to be a 121V resistor so
that it automatically satisfies this condition. Notice that
since the Iadj is typically in the range of 50mA it adds a
small error to the output voltage and should be consid-
ered when very precise output voltage setting is required.
Load Regulation
Since the IRU1176 has separate pins for the output (VOUT)
and the sense (VSENSE), it is ideal for providing true re-
mote sensing of the output voltage at the load. This
means that the voltage drops due to parasitic resistance
such as PCB traces between the regulator and the load
are compensated for using remote sensing. Figure 4
shows a typical application of the IRU1176 with remote
sensing.
Panasonic FA series as well as the Nichicon PL series
insures both stability and good transient response.
Shutdown Operation
The IRU1176 can be disabled by pulling the SD pin low
using an open collector device such as a low cost 2N3904
general purpose transistor as shown in the application
circuit. The current sink of the pin is equal to:
ISINK
=
(VCTRL -
R
1.4)
Where: R=50KV Typically
Thermal Design
The IRU1176 incorporates an internal thermal shutdown
that protects the device when the junction temperature
exceeds the allowable maximum junction temperature.
Although this device can operate with junction tempera-
tures in the range of 150°C, it is recommended that the
selected heat sink be chosen such that during maxi-
mum continuous load operation the junction tempera-
ture is kept below this number. The example below
shows the steps in selecting the proper surface mount
package.
Assuming, the following conditions:
VI N
VC T R L
V IN VOUT
IRU1176
V CTRL
V SENSE
Adj
R1
VOUT = 2.7V
VIN = 3.3V
VCTRL = 5V
IOUT = 2A (DC Avg)
RL Calculate the maximum power dissipation using the fol-
lowing equation:
( )R2
PD = IOUT3(VIN - VOUT)+
IOUT
60
3(VCTRL - VOUT)
Figure 4 - Schematic showing connection
for best load regulation.
Stability
The IRU1176 requires the use of an output capacitor as
part of the frequency compensation in order to make the
regulator stable. Typical designs for the microproces-
sor applications use standard electrolytic capacitors with
typical ESR in the range of 50 to 100mV and an output
capacitance of 500 to 1000mF. Fortunately as the ca-
pacitance increases, the ESR decreases resulting in a
fixed RC time constant. The IRU1176 takes advantage
of this phenomena in making the overall regulator loop
stable.
For most applications a minimum of 100mF aluminum
electrolytic capacitor such as Sanyo, MVGX series,
( )PD = 23(3.3 - 2.7)+
2
60
3(5 - 2.7) = 1.28W
Using table below select the proper package and the
amount of copper board needed.
Pkg Copper θJA(°C/W)
Area
M or P 1.4"x1.4" 25
M or P 1.0"x1.0" 30
M or P 0.7"x0.7" 35
M or P Pad Size 45
Max Pd
(TA=25°C)
4.4W
3.7W
3.1W
2.4W
Max Pd
(TA=45°C)
3.6W
3.0W
2.6W
2.0W
Note: Above table is based on the maximum junction
temperature of 1358C.
As shown in the above table, any of the two packages
will do the job. For lower cost applications the Ultra Thin-
Pak is recommended.
Rev. 1.5
07/16/02
www.irf.com
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet IRU1176.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IRU1175 | 7.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR | International Rectifier |
| IRU1176 | 7.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR | International Rectifier |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |