|
|
Número de pieza | uClamp0511PQ | |
Descripción | 1-Line ESD protection | |
Fabricantes | Semtech Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de uClamp0511PQ (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
No Preview Available ! PROTECTION PRODUCTS - MicroClamp®
Description
The uClampTM series of TVS arrays are designed to pro-
tect sensitive electronics from damage or latch-up due
to ESD. They are designed to replace multilayer varistors
(MLVs) in portable applications. They feature large cross-
sectional area junctions for conducting high transient
currents and offer superior electrical characteristics
such as lower clamping voltage and no device degra-
dation when compared to MLVs. They offer desirable
characteristics for board level protection including fast
response time, low operating and clamping voltage, and
no device degradation.
The µClampTM0511PQ is in a 2-pin, SLP1006P2 pack-
age. It measures 1.0 x 0.6 x 0.5mm. The leads are
spaced at a pitch of 0.65mm and are finished with
lead-free NiPdAu. Each device will protect one bidirec-
tional line operating at ±5 volts. It gives the designer
the flexibility to protect single lines in applications where
arrays are not practical. They may be used to meet the
ESD immunity requirements of IEC 61000-4-2, Level 4
(±15kV air, ±8kV contact discharge). The combination
of small size and high ESD surge capability makes them
ideal for use in portable applications such as cellular
phones, digital cameras, and MP3 players.
The uClamp0511PQ is qualified to AEC-Q100 Grade 1 for
Automotive use.
Package Dimensions
uClamp0511PQ
µClamp®
1-Line ESD protection
Features
Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
Cable Discharge Event (CDE)
Ultra-small package (1.0 x 0.6 x 0.5mm)
Protects one I/O or power line
Low clamping voltage
Working voltage: 5V
Low leakage current
Solid-state silicon-avalanche technology
AEC-Q100 Grade 1 Qualified
Mechanical Characteristics
SLP1006P2 package
Molding compound flammability rating: UL 94V-0
Packaging : Tape and Reel
Lead Finish: NiPdAu
Pb-Free, Halogen Free, RoHS/WEEE Compliant
Applications
Cellular Handsets & Accessories
Cordless Phones
Smart Phones
Notebooks & Handhelds
Portable Instrumentation
Digital Cameras
MP3 Players
Automotive Applications
Schematic & Pin Configuration
10/9/2012
1
SLP1006P2 (Bottom View)
www.semtech.com
1 page PROTECTION PRODUCTS
Applications Information
Device Connection Options
These TVS diodes are designed to protect one data,
I/O, or power supply line. The device is bidirectional and
may be used on lines where the signal polarity can go
above abd below ground.
Circuit Board Layout Recommendations for
Suppression of ESD.
Good circuit board layout is critical for the suppression
of ESD induced transients. The following guidelines are
recommended:
Place the TVS near the input terminals or connectors
to restrict transient coupling.
Minimize the path length between the TVS and the
protected line.
Minimize all conductive loops including power and
ground loops.
The ESD transient return path to ground should be
kept as short as possible.
Never run critical signals near board edges.
Use ground planes whenever possible.
uClamp0511PQ
Equivalent Circuit Diagram
2012 Semtech Corp.
5
www.semtech.com
5 Page |
Páginas | Total 8 Páginas | |
PDF Descargar | [ Datasheet uClamp0511PQ.PDF ] |
Número de pieza | Descripción | Fabricantes |
UCLAMP0511P | 1-Line ESD protection | Semtech Corporation |
uClamp0511PQ | 1-Line ESD protection | Semtech Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |