|
|
PDF RT9451 Data sheet ( Hoja de datos )
| Número de pieza | RT9451 | |
| Descripción | Switch-Mode Single Cell Li-ion Battery Charger | |
| Fabricantes | Richtek Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RT9451 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
®
RT9451
Switch-Mode Single Cell Li-ion Battery Charger with USB OTG
General Description
The RT9451 integrates a high efficiency USB friendly switch
mode charger with On-The-Go (OTG) support for single
cell Li-ion and Li-polymer batteries, D+D− detection, and
a 50mA LDO regulator into a single chip.
The charger features a synchronous 375kHz PWM
controller with integrated power MOSFETs, input current
sensing and regulation, Minimum Input Voltage Regulation
(MIVR), high accuracy charge current and voltage
regulation, and charge termination. It charges the battery
in three phases : low current pre-charge, constant current
fast charge, and constant voltage trickle charge. The input
current is automatically limited to the value set by the
host. The charger can be configured to terminate charge
based on user-selectable minimum current level and
automatically restart the charge cycle if the battery voltage
falls below the recharge threshold. A safety timer with
reset control provides a safety backup for I2C interface.
The charger automatically enters sleep mode or high
impedance mode when the input supply is removed. The
charge status is reported to the host using the I2C interface
and the STAT pin. The D+D− detection circuit allows
automatic detection of a USB wall charger. If a wall charger
is detected, the input current limit will automatically
increase from 500mA to 975mA.
In OTG mode, the PWM controller boosts the battery
voltage to 5V and provides up to 1.6A of current to the
USB output. At very light load, the Boost operates in burst
mode to optimize efficiency. OTG mode can be enabled
either through I2C interface or GPIO control.
Applications
z Mobile Phones and Smart Phones
z MP3 Players
z Handheld Devices
Ordering Information
RT9451
Package Type
QW : WQFN-32L 4x4 (W-Type)
Lead Plating System
G : Green (Halogen Free and Pb Free)
Note :
Richtek products are :
` RoHS compliant and compatible with the current require-
ments of IPC/JEDEC J-STD-020.
` Suitable for use in SnPb or Pb-free soldering processes.
Simplified Application Circuit
RT9451
VIN VIN MID
CIN
Control
Inputs
USB Charger
Detection
SCL
SDA
LX
VIO
DP
DM BATS
GND
CMID
L
CSYSS + Battery
Copyright ©2013 Richtek Technology Corporation. All rights reserved.
DS9451-00 September 2013
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
1
1 page  
RT9451
Absolute Maximum Ratings (Note 1)
z Supply Voltage VIN -------------------------------------------------------------------------------------------------------- −0.3V to 28V
z MID, BOOT to PGND ------------------------------------------------------------------------------------------------------ −0.3V to 28V
z Other Pins -------------------------------------------------------------------------------------------------------------------- −0.3V to 6V
z VISENL to VISENR ------------------------------------------------------------------------------------------------------------ ±6V
z Output Current (average) LX --------------------------------------------------------------------------------------------- 4A
z Output Current (continuous) LDO -------------------------------------------------------------------------------------- 100mA
z Power Dissipation, PD @ TA = 25°C
WQFN-32L 4x4 ------------------------------------------------------------------------------------------------------------- 3.59W
z Package Thermal Resistance (Note 2)
WQFN-32L 4x4, θJA -------------------------------------------------------------------------------------------------------- 27.8°C/W
WQFN-32L 4x4, θJC ------------------------------------------------------------------------------------------------------- 7°C/W
z Junction Temperature ------------------------------------------------------------------------------------------------------ 150°C
z Lead Temperature (Soldering, 10 sec.) -------------------------------------------------------------------------------- 260°C
z Storage Temperature Range --------------------------------------------------------------------------------------------- −65°C to 150°C
z ESD Susceptibility (Note 3)
HBM (Human Body Model) ----------------------------------------------------------------------------------------------- 2kV
MM (Machine Model) ------------------------------------------------------------------------------------------------------ 200V
Recommended Operating Conditions (Note 4)
z Supply Input Voltage Range, VIN --------------------------------------------------------------------------------------- 4.3V to 12V
z Junction Temperature Range --------------------------------------------------------------------------------------------- −40°C to 125°C
z Ambient Temperature Range --------------------------------------------------------------------------------------------- −40°C to 85°C
Electrical Characteristics
(VBATS = 3.6V ± 5%, TA = 25°C, unless otherwise specified)
Parameter
Symbol
Test Conditions
Input Currents
Battery Discharge
Current in High
Impedance Mode
(ISENL, ISENR, LX,
BATS Pins)
High Impedance Mode,
IDISCHARGE VBATS = 4.2 V SDA = SCL = 0
VIN Supply Current IQ
Charger PWM ON
VIN > VIN(MIN) Charger PWM OFF
Voltage Regulation
Output Charge Voltage VOREG
Voltage Regulation
Accuracy
Operating in voltage regulation,
programmable
0 to 85°C
Min Typ Max Unit
-- 2 30 μA
-- 10000 --
μA
-- -- 5000
3.5 -- 4.44 V
−1 -- 1 %
Copyright ©2013 Richtek Technology Corporation. All rights reserved.
DS9451-00 September 2013
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
5
5 Page 
Typical Operating Characteristics
Charge Mode
Efficiency vs. Battery Voltage
100
95
90
85 ICHRG = 1A
ICHRG = 1.4A
80 ICHRG = 1.8A
ICHRG = 2.2A
75 ICHRG = 2.6A
ICHRG = 3A
70
65
VIN = 5V
60
3.4 3.5 3.6 3.7 3.8 3.9 4 4.1 4.2
Battery Voltage (V)
Adapter Insertion
RT9451
Efficiency vs. Battery Voltage
100
95
90
85 ICHRG = 1A
80 ICHRG = 1.4A
ICHRG = 1.8A
75 ICHRG = 2.2A
ICHRG = 2.6A
70 ICHRG = 3A
65
VIN = 9V
60
3.4 3.5 3.6 3.7 3.8 3.9 4 4.1 4.2
Battery Voltage (V)
Battery Removal
VIN
(5V/Div)
STAT
(2V/Div)
LX
(10V/Div)
IIN
(200mA/Div)
VIN = 5V, VBAT = 3.7V
Time (10ms/Div)
STAT
(2V/Div)
LX
(5V/Div)
VBAT
(1V/Div)
ILX
(1A/Div)
VIN = 5V, VBAT = 3.7V, TERM_EN = 1
Time (5ms/Div)
Bad Adapter
VIN
(5V/Div)
INT
(5V/Div)
IIN
(20mA/Div)
VIN = 5V/10mA, VBAT = 3.7V
Time (10ms/Div)
Copyright ©2013 Richtek Technology Corporation. All rights reserved.
DS9451-00 September 2013
Minimum Input Voltage Regulation
No AICR
INT
(5V/Div)
VIN
(2V/Div)
IIN
(1A/Div)
VIN = 5V/1A, ICHRG = 2A,
VMIVR = 4.76V, VBAT = 3.7V
Time (250μs/Div)
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet RT9451.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RT9451 | Switch-Mode Single Cell Li-ion Battery Charger | Richtek Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |