DataSheet.jp

RT8492 の電気的特性と機能

RT8492のメーカーはRichtekです、この部品の機能は「High Voltage 4-CH LED Driver Controller」です。


製品の詳細 ( Datasheet PDF )

部品番号 RT8492
部品説明 High Voltage 4-CH LED Driver Controller
メーカ Richtek
ロゴ Richtek ロゴ 




このページの下部にプレビューとRT8492ダウンロード(pdfファイル)リンクがあります。
Total 20 pages

No Preview Available !

RT8492 Datasheet, RT8492 PDF,ピン配置, 機能
®
RT8492
High Voltage 4-CH LED Driver Controller
General Description
The RT8492 is a 4-CH LED driver controller that delivers
well matched LED current to each channel of LED string.
With external current sources, the number of LEDs per
string is only limited by the current source and the VIN/
VOUT conditions. The current mode PWM boost type
controller operates at a programmable switching frequency
of up to 1MHz, with a wide VIN range covering from 9V to
32V. The switch driver is designed to drive industrial grade
high power MOSFETs.
The PWM loop selects and regulates the LED string with
the highest voltage string to 0.9V, thus allowing voltage
mismatches between the LED strings. The RT8492
automatically detects and excludes any open and/short
strings during operation from the PWM loop to prevent
VOUT from over voltage.
The RT8492 also provides LED short protection. If LED
short occurs and causes any LEDx but not all LEDx pin
voltage greater than 8V, the CAP pin is charged up by
internal 10μA. If the LED short condition lasts longer than
the CAP pin voltage reaches 3.5V, the FLAG pin will go
high and the GATE pin will be kept low immediately until
the CAP pin voltage drops below 3.5V. The delay time is
programmable by the capacitor at the CAP pin.
Features
Wide Operation Voltage Range : 9V to 32V
Programmable Channel Current
3% Current Matching Accuracy between Channels
Programmable Switching Frequency
Easy Analog and Digital Dimming Control
Programmable Soft-Start
LED Open Channel Detection and Protection
LED Short-Fault Detect Latch Off Multiple LED
Strings
Programmable Output Over Voltage Protection
Under Voltage Lockout and Thermal Shutdown
28-Lead TSSOP Package
Applications
Building and Street Lighting
LED TV Backlight
LED Monitor Backlight
Industrial Display Backlight
Simplified Application Circuit
VIN
R3
12V
CIN
CVCC
CB
RSET
RT8492
VCC
CAP
VBASE
GBIAS
GATE
ISENSE
ACTL
NC
FLAG
LED1
RSET
GATE1
SENSE1
L1
CT
Chip Enable
EN
SS
CSS
GND
LED4
GATE4
SENSE4
D1
COUT
MSW
RSENSE
M1
RS1
VOUT
4 x N LEDs
M4
RS4
Copyright ©2014 Richtek Technology Corporation. All rights reserved.
DS8492-06 October 2014
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
1

1 Page





RT8492 pdf, ピン配列
RT8492
Functional Pin Description
Pin No.
1
2
3
Pin Name
Pin Function
VCC
Power Supply. For good bypass, a low ESR capacitor is needed between this pin
and GND.
VBASE
The External Gate Bias Supply is Driven by an External NPN Transistor. The base
of this NPN is tied to VBASE pin. The emitter of this NPN is tied to GBIAS pin. The
collector of this NPN is tied to VCC.
GBIAS
Internal Gate Driver Bias Voltage (around 9.5V). Need a good bypass capacitor
between this pin and GND.
4
GATE
Gate Pin of External MOSFET. For the Boost PWM control loop.
5 GND Ground.
Switch Current Sense. Connect a sense resistor from this pin to GND. The switch
6 ISENSE current sense signal is used for boost current mode PWM loop control and power
switch over current protection.
7
RSET
Switching Frequency Set. Put a resistor from RSET to GND to program the
switching frequency. fSW = 280kHz when RSET = 40k.
8 EN
Chip Enable (Active High).
9
OVP
Over Voltage Protection. OVP pin threshold is around 1.25V. Use a resistor divider
from output to GND to program the OVP level.
10 SS
Soft-Start Pin. Use a soft-start cap from SS pin to GND to program the soft-start time
period. Around 10A is sourcing out of SS pin.
11 VC
Loop Compensation.
12
ACTL
Analog/PWM Dimming Control. When used in analog dimming, ACTL control range
is from 0.4V to 1.4V.
Fault Indicator Output. Flag pin goes high in two conditions. As the OVP pin goes
high, the FLAG pin goes high without time delay. If the LED short condition occurs
13 FLAG and the CAP pin voltage is higher than 3.5V, the FLAG pin will go high and the
GATE pin will be pulled low and latched off. The latch-off condition can be reset by
EN pin or VCC pin.
14 CAP
The LED Short Detection Time Delay Programming. If LED short occurs and causes
any LEDx but not all LEDx pin voltage greater than 8V, the CAP pin is charged up
by internal 10A. If the LED short condition occurs and lasts longer than the CAP
pin voltage reaches 3.5V, the FLAG pin will go high. The delay time is
programmable by the capacitor at the CAP pin. The typical delay time is 80ms when
the capacitor at CAP pin is 47nF.
24, 21, 18, 15 SENSEx
25, 22, 19, 16 GATEx
26, 23, 20, 17 LEDx
27, 28
NC
Source Pin of External MOSFETx (x = 1 to 4).
The SENSEx pins are regulated around 440mV. Connect a sense resistor from this
pin to GND. The LED current is programmed by ILED = 440mV / (sense resistance)
when VACTL is greater than 1.4V.
Gate Pin of External MOSFETx (x = 1 to 4). For LED drivers.
LEDx Pin (x = 1 to 4) is Normally Regulated Around 0.9V. If LED short occurs and
causes any LEDx but not all LEDx pin voltage greater than 8V, the LED short
protection is triggered.
Connect to LED1.
Copyright ©2014 Richtek Technology Corporation. All rights reserved.
DS8492-06 October 2014
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
3


3Pages


RT8492 電子部品, 半導体
RT8492
Absolute Maximum Ratings (Note 1)
VCC --------------------------------------------------------------------------------------------------------------------------- 0.3 to 36V
ISENSE
DC ------------------------------------------------------------------------------------------------------------------------------ 0.3 to 2V
< 200ns ----------------------------------------------------------------------------------------------------------------------- 0.3 to 6V
GBIAS ------------------------------------------------------------------------------------------------------------------------- 0.3 to 14V
SENSE1 to SENSE4
DC ------------------------------------------------------------------------------------------------------------------------------ 0.3 to 1V
< 200ns ----------------------------------------------------------------------------------------------------------------------- 0.3 to 6V
LED1 to LED4 (Note 2) -------------------------------------------------------------------------------------------------- 0.3 to 20V
ACTL, EN, OVP ------------------------------------------------------------------------------------------------------------ 0.3 to 10V
Power Dissipation, PD@TA = 25°C
TSSOP-28 -------------------------------------------------------------------------------------------------------------------- 0.67W
Package Thermal Resistance (Note 3)
TSSOP-28, θJA -------------------------------------------------------------------------------------------------------------- 147.8°C/W
Junction Temperature ------------------------------------------------------------------------------------------------------ 150°C
Storage Temperature Range --------------------------------------------------------------------------------------------- 65°C to 150°C
Lead Temperature (Soldering, 10 sec.) -------------------------------------------------------------------------------- 260°C
ESD Susceptibility (Note 4)
HBM (Human Body Model) ----------------------------------------------------------------------------------------------- 2kV
MM (Machine Model) ------------------------------------------------------------------------------------------------------ 200V
Recommended Operating Conditions (Note 5)
Supply Voltage, VCC ----------------------------------------------------------------------------------------------------- 9V to 32V
Junction Temperature Range -------------------------------------------------------------------------------------------- 40°C to 125°C
Ambient Temperature Range -------------------------------------------------------------------------------------------- 40°C to 85°C
Electrical Characteristics
(VCC = 12V, No Load, TA = 25°C, unless otherwise specified)
Parameter
Symbol
Test Conditions
Overall
Supply Current
Shutdown Current
EN Threshold
Voltage
EN Input Current
Logic-High
Logic-Low
LED Current Programming
SENSE1 to SENSE4 Threshold
IVCC
ISHDN
VIH
VIL
IEN
VVC 0.4V (Switching off)
VEN 1.2V
VEN 3.3V
6V > VGATEx > 2V
SENSE Voltage CH to CH Matching
V(MAX) V(MIN)
2V(avg)
Analog Dimming ACTL Input Current IACTL
VACTL 6V
Min Typ Max Unit
-- 5 10 mA
-- 5 20 A
2 -- -- V
-- -- 0.5
-- 2 10 A
418 440 462 mV
-- 1 2 %
-- 10 30 A
Copyright ©2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
6
is a registered trademark of Richtek Technology Corporation.
DS8492-06 October 2014

6 Page



ページ 合計 : 20 ページ
 
PDF
ダウンロード
[ RT8492 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
RT8491

High Voltage 6-CH LED Driver Controller

Richtek
Richtek
RT8492

High Voltage 4-CH LED Driver Controller

Richtek
Richtek
RT8494

High Voltage High Current LED Driver Controller

Richtek
Richtek
RT8496

High Voltage High Current LED Driver Controller

Richtek
Richtek


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap