|
MQ-5 の電気的特性と機能
|
MQ-5のメーカーはWinsen Electronicsです、この部品の機能は「Semiconductor Sensor」です。 |
|
|
製品の詳細 ( Datasheet PDF )
| 部品番号 MQ-5 |
| 部品説明 Semiconductor Sensor |
| メーカ Winsen Electronics |
ロゴ |
このページの下部にプレビューとMQ-5ダウンロード（pdfファイル）リンクがあります。 Total 3 pages |
No Preview Available ! |
Zhengzhou Winsen Electronics Technology Co., Ltd
www.winsensor.com
MQ-5 Semiconductor Sensor for Combustible Gas
Sensitive material of MQ-5 gas sensor is SnO2, which with lower conductivity in clean air. When the
target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration
rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of
gas concentration.
MQ-5 gas sensor has high sensitity to Methane, Propane and Butane, and could be used to detect
both Methane and Propane. The sensor could be used to detect different combustible gas especially
Methane, it is with low cost and suitable for different application.
Character
Configuration
* Good sensitivity to Combustible gas in wide range
* High sensitivity to Methane, Butane and Propane
* Long life and low cost
* Simple drive circuit
Application
* Domestic gas leakage detector
* Industrial Combustible gas detector
* Portable gas detector
Technical Data
Basic test loop
Model No.
Sensor Type
Standard Encapsulation
Detection Gas
Concentration
Loop Voltage Vc
Circuit
Heater Voltage
Load
Resistance
VH
RL
Heater
Resistance
RH
Character
Heater
consumption
Sensing
Resistance
PH
Rs
Sensitivity S
Slope
α
Tem. Humidity
Condition Standard test circuit
Preheat time
MQ-5
Semiconductor
Bakelite (Black Bakelite)
LPG, Methane, coal gas
300-10000ppm( Methane,
Propane, Butane, H2)
≤24V DC
5.0V±0.2V AC or DC
Adjustable
31Ω±3Ω Room Tem.
≤900mW
2KΩ-20KΩ(in 2000ppm C3H8 )
Rs(in air)/Rs(1000ppm C3H8)≥5
≤0.6(R1000ppm/R500ppm H2)
20 ±2 65%±5%RH
Vc:5.0V±0.1V
VH: 5.0V±0.1V
Over 48 hours
Vc VRL
RL
VH
GND
The above is basic test circuit of the sensor.
The sensor need to be put 2 voltage,
heater voltage VH and test voltage VC .
VH used to supply certified working
temperature to the sensor, while VC used
to detect voltage (VRL) on load resistance
RL whom is in series with sensor. The
sensor has light polarity, Vc need DC
power. VC and VH could use same power
circuit with precondition to assure
performance of sensor. In order to make
the sensor with better performance,
suitable RL value is needed:
Power of Sensitivity body(Ps):
Tel: 86-371-67169097 Fax: 86-371-60932988
Email: sales@winsensor.com
1 Page
Zhengzhou Winsen Electronics Technology Co., Ltd
www.winsensor.com
Notification
1 Following conditions must be prohibited
1.1 Exposed to organic silicon steam
Organic silicon steam cause sensors invalid, sensors must be avoid exposing to silicon bond,
fixature, silicon latex, putty or plastic contain silicon environment
1.2 High Corrosive gas
If the sensors exposed to high concentration corrosive gas (such as H2Sz, SOX Cl2 HCl etc), it will
not only result in corrosion of sensors structure, also it cause sincere sensitivity attenuation.
1.3 Alkali, Alkali metals salt, halogen pollution
The sensors performance will be changed badly if sensors be sprayed polluted by alkali metals salt
especially brine, or be exposed to halogen such as fluorin.
1.4 Touch water
Sensitivity of the sensors will be reduced when spattered or dipped in water.
1.5 Freezing
Do avoid icing on sensor’surface, otherwise sensor would lose sensitivity.
1.6 Applied voltage higher
Applied voltage on sensor should not be higher than stipulated value, otherwise it cause down-line or
heater damaged, and bring on sensors’ sensitivity characteristic changed badly.
1.7 Voltage on wrong pins
For 6 pins sensor, if apply voltage on 1 3 pins or 4 6 pins, it
will make lead broken, and without signal when apply on 2 4 pins
2 Following conditions must be avoided
2.1 Water Condensation
Indoor conditions, slight water condensation will effect sensors performance lightly. However, if water
condensation on sensors surface and keep a certain period, sensor’ sensitivity will be decreased.
2.2 Used in high gas concentration
No matter the sensor is electrified or not, if long time placed in high gas concentration, if will affect
sensors characteristic.
2.3 Long time storage
The sensors resistance produce reversible drift if it’s stored for long time without electrify, this drift is
related with storage conditions. Sensors should be stored in airproof without silicon gel bag with clean air.
For the sensors with long time storage but no electrify, they need long aging time for stbility before using.
2.4 Long time exposed to adverse environment
No matter the sensors electrified or not, if exposed to adverse environment for long time, such as
high humidity, high temperature, or high pollution etc, it will effect the sensors performance badly.
2.5 Vibration
Continual vibration will result in sensors down-lead response then repture. In transportation or
assembling line, pneumatic screwdriver/ultrasonic welding machine can lead this vibration.
2.6 Concussion
If sensors meet strong concussion, it may lead its lead wire disconnected.
2.7 Usage
For sensor, handmade welding is optimal way. If use wave crest welding should meet the following
conditions:
2.7.1 Soldering flux: Rosin soldering flux contains least chlorine
2.7.2 Speed: 1-2 Meter/ Minute
2.7.3 Warm-up temperature 100±20
2.7.4 Welding temperature 250±10
2.7.5 1 time pass wave crest welding machine
If disobey the above using terms, sensors sensitivity will be reduced.
Tel: 86-371-67169097 Fax: 86-371-60932988
Email: sales@winsensor.com
3Pages
合計 : 3 ページ |
| PDF ダウンロード [ MQ-5 データシート.PDF ] |
|
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
|
|
| 部品番号 | 部品説明 | メーカ |
| MQ-1168 | Evaluation Board Users Guide |  MediaQ |
| MQ-1168 | Multimedia Platform Controller | MediaQ |
| MQ-131 | GAS SENSOR |  ETC |
| MQ-135 | Gas Sensor |  Hanwei |