|
MIW1526 の電気的特性と機能
|
MIW1526のメーカーはTotal Power Internationalです、この部品の機能は「3 Watts 2 :1 Wide Input Range DC/DC Converters」です。 |
|
|
製品の詳細 ( Datasheet PDF )
| 部品番号 MIW1526 |
| 部品説明 3 Watts 2 :1 Wide Input Range DC/DC Converters |
| メーカ Total Power International |
ロゴ |
このページの下部にプレビューとMIW1526ダウンロード（pdfファイル）リンクがあります。 Total 8 pages |
No Preview Available ! |
www.DataSheet4U.com
TOTAL POWER INT'L
MIW1500 Series
3 Watts 2 :1 Wide Input Range DC/DC Converters
Single and Dual Outputs
Key Features
Ÿ High Efficiency up to 82%
Ÿ 2:1 Input Range
Ÿ I/O Isolation 1500VDC
Ÿ Industry Standard Pinout
Ÿ SMT Technology
Ÿ Short Circuit Protection
Ÿ EMI Complies With EN55022 Class A
Ÿ MTBF > 1,000,000 Hours
MIW1500-Series power modules are low-profile
dc-dc converters that operate over input voltage ranges of
4.5-9VDC, 9-18VDC, 18-36VDC and provide precisely regulated
output voltages of 5V, 12V, {12V and {15V.
The -25] to +71] operating temperature range makes it ideal
for data communication equipments, mobile battery driven
equipments, distributed power systems, telecommunication
equipments, mixed analog/digital subsystems, process/machine
control equipments, computer peripheral systems and industrial
robot systems.
The modules have a maximum power rating of 3W and a typical
full-load efficiency of 82%, continuous short circuit, 60mA output
ripple, built-in filtering for both input and output minimizes the need
for external filtering.
$
Low Cost
1500
VDC
I/O Isolation
EMI
EN55022
2:1
Wide Range
Block Diagram
Single Output
Dual Output
LC
+Vin Filter
-Vin
PFM
Isolation Ref.Amp
+Vo LC
+Vin Filter
-Vo
-Vin
PFM
Isolation Ref.Amp
+Vo
Com.
-Vo
1 Page
www.DataSheet4U.com
TOTAL POWER INT'L
MIW1500 Series
Input Specifications
Parameter
Start Voltage
Under Voltage Shutdown
Reverse Polarity Input Current
Short Circuit Input Power
Input Filter
Model
5V Input Models
12V Input Models
24V Input Models
5V Input Models
12V Input Models
24V Input Models
All Models
Min.
3.5
4.5
8
---
---
---
---
---
Typ.
Max.
4 4.5
79
12 18
3.5 4
6.5 8.5
11 17
---
1
1000
2000
Pi Filter
Unit
VDC
A
mW
Output Specifications
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20MHz)
Ripple & Noise (20MHz)
Ripple & Noise (20MHz)
Over Power Protection
Transient Recovery Time
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
Conditions
Dual Output , Balanced Loads
Vin=Min. to Max.
Io=10% to 100%
Over Line,Load & Temp
25% Load Step Change
Min.
---
---
---
---
---
---
---
120
---
---
---
Continuous
Typ.
{0.5
{0.5
{0.2
{0.2
45
---
---
---
300
{3
{0.01
Max.
{2.0
{2.0
{0.5
{0.5
60
100
15
---
500
{6
{0.02
Unit
%
%
%
%
mV P-P
mV P-P
mV rms.
%
uS
%
%/]
General Specifications
Parameter
Isolation Voltage Rated
Isolation Voltage Test
Isolation Resistance
Isolation Capacitance
Switching Frequency
MTBF
Conditions
60 Seconds
Flash Tested for 1 Second
500VDC
100KHz,1V
MIL-HDBK-217F @ 25], Ground Benign
Min.
1500
1650
1000
---
---
1000
Typ.
---
---
---
---
300
---
Max.
---
---
---
500
---
---
Unit
VDC
VDC
M[
pF
KHz
K Hours
Capacitive Load
Models by Vout
Maximum Capacitive Load
Note: # For each output .
5V
12V
{12V #
{15V #
Unit
470 470 220 220
uF
3Pages
www.DataSheet4U.com
TOTAL POWER INT'L
MIW1500 Series
Test Configurations
Overcurrent Protection
Input Reflected-Ripple Current Test Setup
To Oscilloscope
+Vin +Out
+ + Lin
Battery Cin
Current DC / DC
Probe Converter
-Vin -Out
Load
Input reflected-ripple current is measured with a inductor
Lin (4.7uH) and Cin (220uF, ESR < 1.0[ at 100 KHz) to
simulate source impedance.
Capacitor Cin, offsets possible battery impedance.
Current ripple is measured at the input terminals of the
module, measurement bandwidth is 0-500 KHz.
To provide protection in a fault (output overload)
condition, the unit is equipped with internal current limiting
circuitry and can endure current limiting for an unlimited
duration. At the point of current-limit inception, the unit shifts
from voltage control to current control. The unit operates
normally once the output current is brought back into its
specified range.
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power module.
In applications where power is supplied over long lines
and output loading is high, it may be necessary to use a
capacitor at the input to ensure startup.
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.47uF ceramic capacitor.
Scope measurement should be made by using a BNC
socket, measurement bandwidth is 0-20 MHz. Position the
load between 50 mm and 75 mm from the DC/DC Converter.
Capacitor mounted close to the power module helps
ensure stability of the unit, it is recommended to use a good
quality low Equivalent Series Resistance (ESR < 1.0[ at 100
KHz) capacitor of a 8.2uF for the 5V input devices, a 3.3uF for
the 12V input devices and a 1.5uF for the 24V devices.
Output Ripple Reduction
+Vin
+Out
Single Output
DC / DC
Converter
-Vin
-Out
Copper Strip
Cout
Scope
Resistive
Load
+
DC Power
Source
-
+Vin
+ DC / DC
Converter
Cin
-Vin
+Out
-Out
Load
+Vin
+Out
Dual Output
DC / DC Com.
Converter
-Vin
-Out
Copper Strip
Cout
Cout
Scope
Resistive
Load
Scope
A good quality low ESR capacitor placed as close as
practicable across the load will give the best ripple and
noise performance.
To reduce output ripple, it is recommended to use 3.3uF
capacitors at the output.
Design & Feature Considerations
Maximum Capacitive Load
+
DC Power
Source
-
+Vin
+Out
Single Output
DC / DC
Converter
-Vin
-Out
Cout
Load
The MIW1500 series has limitation of maximum
connected capacitance at the output.
The power module may be operated in current limiting
mode during start-up, affecting the ramp-up and the startup
time.
For optimum performance we recommend 220uF
maximum capacitive load for dual outputs and 470uF
capacitive load for single outputs.
The maximum capacitance can be found in the data.
+
DC Power
Source
-
+Vin
+Out
Dual Output
DC / DC Com.
Converter
-Vin
-Out
Cout
Load
6 Page
合計 : 8 ページ |
| PDF ダウンロード [ MIW1526 データシート.PDF ] |
|
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
|
|
| 部品番号 | 部品説明 | メーカ |
| MIW1522 | 3 Watts 2 :1 Wide Input Range DC/DC Converters | Total Power International |
| MIW1522 | Single & Dual Output DC/DC Converters |  Minmax Technology |
| MIW1523 | 3 Watts 2 :1 Wide Input Range DC/DC Converters | Total Power International |
| MIW1523 | Single & Dual Output DC/DC Converters | Minmax Technology |